Full C

Scientific Reports volume 13, Article number: 3623 (2023) Cite this article

652 Accesses

Metrics details

We demonstrate a full C-band wavelength-tunable mode-locked fiber laser with a repetition rate of 250 MHz, representing the highest repetition rate for C-band tunable mode-locked lasers thus far to the best of our knowledge. The polarization-maintaining fiber-based Fabry–Perot cavity enables a fundamental repetition rate of 250 MHz with a semiconductor saturable absorber mirror as a mode-locker. We observed a stable and single soliton mode-locking state with wide tunability of the center wavelength from 1505 to 1561 nm by adjusting the incident angle of a bandpass filter inside the cavity. The wavelength-tunable high-repetition-rate mode-locked laser covering the full C-band is expected to be a compelling source for many frequency-comb-based applications, including high-precision optical metrology, broadband absorption spectroscopy, and broadband optical frequency synthesizers.

High-repetition-rate mode-locked lasers, given their unique characteristics of an ultra-short pulse, high peak power and a broad spectrum, have played key roles in numerous applications, including frequency comb generation1, remote timing transfer and synchronization2, broadband spectroscopy3, microwave generation4, length metrology5,6,7,8, surface metrology9 and observations of ultrafast phenomena10. In particular, fiber-based mode-locked lasers have been widely used as a practical tool given their reliability, compactness and low cost11.

To create a high-repetition-rate mode-locked laser, the common methods are harmonic mode-locking and shortening of the cavity length. In the former method, ensuring the stable operation of harmonic mode-locking involves many technical challenges related to super-mode noise, such as a low signal-to-noise ratio and degradation of the pulse timing jitter12. Contrary to harmonic mode-locking, scaling up the fundamental repetition rate while shortening the cavity length can stably generate ultra-short pulses with better spectral purity and timing jitter13. With regard to fiber lasers, they are commonly designed with a Fabry–Perot cavity because some components can be placed outside of the cavity14.

Mode-locking is commonly realized by nonlinear polarization evolution (NPE)15 and a real saturable absorber (SA)16. The NPE technique has advantages with regard to the characteristics of the pulses, such as ultra-short pulse generation and a broad spectrum. However, turn-key operation scarcely works for NPE based mode-locked lasers. Contrary to the NPE technique, SAs, which are based on saturable absorption materials and demonstrated with semiconductors17, carbon nanotubes18, graphene19, and 2D materials20, offer the advantages of turn-key operation and self-mode-locking. SAs are suitable for high-repetition-rate mode-locked lasers because they only require a small area in the cavity. SA-based mode-locked lasers are typically operated in the soliton pulse regime, where the cavity net dispersion and self-phase modulation are well balanced21. However, compared to NPE-based mode-locked lasers, SA-based mode-locked lasers have a broader pulse width and narrower spectral bandwidth. Typically, SA-based mode-locked lasers have pulse durations of a few hundreds of femtoseconds and spectral bandwidths of a few nanometers on the C-band22. To generate a broadband optical spectrum and an ultra-short pulse, nonlinear fiber-based spectral broadening with power amplification is exploited as a common method. Instead of the complicated and onerous method of nonlinear spectral broadening, tuning the center wavelength of a mode-locked laser is one feasible alternative to cover a broad spectral range via a simple approach.

Figure 1 presents an overview of C-band tunable mode-locked fiber laser results in terms of the tuning range of the center wavelength and pulse repetition rate on a logarithmic scale18,23,24,25,26,27,28,29,30,31,32,33,34,35. Wavelength-tunable mode-locked fiber lasers operating on the C-band have been demonstrated with various ways of tuning the center wavelength, including a tunable bulk filter18,23,26,35, an intrinsic cavity birefringence effect24,29,33,34, an extendable grating25, a 45°-tilted fiber grating27,31, a super-mode interference effect28 and a grating with a tuning aperture30,32. Thus far, C-band tunable mode-locked lasers have only been demonstrated at repetition rates below the range of tens of MHz, while the tunable range of the center wavelength already covers the full C-band. These types of mode-locked lasers with a low repetition rate are suitable for laser machining and high-power amplification, but their repetition rates are still too low for a majority of frequency-comb-based optical metrology applications13,36.

Summary of state-of-the-art C-band tunable mode-locked lasers in terms of the repetition rate and tuning range on the C-band.

In our previous study, we demonstrated for the first time a widely wavelength-tunable mode-locked fiber laser operating at a repetition rate of more than 100 MHz35. The Fabry–Perot cavity-based optical design enabled a high-repetition-rate mode-locked fiber laser with full C-band tunability. In this study, we report a full C-band tunable mode-locked polarization-maintaining fiber mode-locked laser operating at a fundamental repetition rate of 250 MHz, which is the highest repetition rate for a C-band tunable mode-locked fiber laser thus far to the best of our knowledge. Such a high repetition rate makes it easy to phase-lock or to monitor the optical frequency of a continuous-wave laser. The polarization-maintaining fiber structure enables robust and turn-key operation without intra-cavity polarization adjustments and offers robust and stable mode-locking operation13,22,37. A semiconductor saturable absorber mirror (SESAM), commonly adopted as a well-verified, reliable, and stable mode-locker, was exploited as both an end mirror for the Fabry–Perot laser cavity and as a device to realize mode-locking with turn-key operation. A bulk optical bandpass filter was used to minimize the laser cavity length. The transmission band can easily be adjusted by changing the incidence angle of the optical band pass filter38. We observed a stable mode-locking state with a center wavelength from 1505 to 1561 nm. Pulse durations typically ranged from 640 fs to 2.8 ps and the spectral bandwidths (3-dB) were typically in the range of 0.9 nm to 5.1 nm. Measured output power levels exceeded 5 mW regardless of the center wavelength, making it sufficient for use in most frequency comb applications, including high-precision dimensional metrology, broadband absorption spectroscopy, and broadband optical frequency synthesizers. More importantly, it is expected that the signal-to-noise ratio in optical metrology can be improved, as the individual comb modes of the proposed mode-locked laser can have significantly more optical power than compared to the power levels offered by previous wavelength-tunable mode-locked lasers.

Figure 2a shows the optical layout of the proposed C-band wavelength-tunable mode-locked polarization-maintaining erbium-doped fiber laser. The design of the laser cavity is based on a fiber Fabry–Perot type of linear cavity with polarization-maintaining (PM) fiber to maintain intra-cavity polarization for robust operation. The laser cavity consists of polarization-maintaining erbium-doped fiber (PM EDF, PM-ESF-7/125, Nufern) as a gain medium, a free space part with a bulk optical bandpass filter having a 3-db bandwidth of 50 nm (7527: 1550–50 OD4, Alluxa), single-mode polarization-maintaining fiber, and the aforementioned SESAM (SAM-1550–23-2 ps, BATOP), which is a critical component for self-starting mode-locking and for the determination of the pulse characteristics39. The 430 mm laser cavity consists of 300 mm of PM EDF with anomalous dispersion, 60 mm of standard PM fiber and 70 mm of free space with a bulk optical band pass filter. The round-trip cavity dispersion was estimated to be -0.015 ps2, allowing the laser to operate in the soliton mode-locking state. The free-space part was about 70 mm and can be moved to adjust the repetition rate. The fiber-to-free-space-to-fiber coupling loss is less than 1 dB (20%). The optical bandpass filter installed in the free space part was used to tune the center wavelength of the mode-locked laser by adjusting the incidence angle. If the incidence angle of the intra-cavity light is tilted away from the normal direction (or if the incidence angle is 0°), the transmission spectrum of the optical bandpass filter will shift toward a shorter wavelength (blue shift) according to the following equation,

where λtilt is the transmitted wavelength when the optical bandpass filter is tilted at an incidence angle of θ, λnormal is the transmitted wavelength when the optical bandpass filter is normal to the incoming light, no is the refractive index of the incident medium, and neff is the effective refractive index of the optical bandpass filter. Figure 2b shows numerical simulation results of the transmission curve of the optical bandpass filter used in this study versus the incidence angle. Also, the center wavelengths of the mode-locked laser were compared to the transmission curve of the optical bandpass filter versus the incidence angle. These results will be described in more detail in the following section.

Layout of the full C-band tunable mode-locked polarization-maintaining fiber laser: (a) optical layout of the laser cavity of the C-band tunable mode-locked laser. C: fiber collimator. BPF: bandpass filter, WDM: wavelength multiplexer, Pump LD: pump laser diode. (b) Transmission curve of the bandpass filter versus the incidence angle. Red dots indicate the measured center wavelength of the mode-locked laser versus the incidence angle.

The end mirrors of the laser cavity consisted of a dichroic coating at the FC/PC connector and the SESAM. Both end mirrors worked multi-functionally to reduce the number of optical components inside the laser cavity and minimize the length of the laser cavity. The dichroic coating at the end of the polarization-maintaining erbium-doped fiber was designed with 90% reflectance and 10% transmittance at a wavelength of 1550 nm and with 100% transmittance at a wavelength of 980 nm. The dichroic coating acted as an output coupler at a wavelength of 1550 nm but was transparent at a wavelength of 980 nm for optical pumping. The pumping laser with a wavelength of 980 nm was incident outside of the laser cavity from the PM fiber wavelength multiplexer (WDM) and the output signal of the mode-locked laser was emitted from the dichroic coating as an output coupler. The SESAM, which has a 14% modulation depth, 9% non-saturable loss and a 2 ps relaxation time constant, was butt-coupled to the FC/PC connector of the standard PM fiber and acted as both a mode-locker and an end mirror. In this work, we propose an optical layout without fiber fusion splicing despite the coupling loss, making this design beneficial for assembly and maintenance.

At shorter center wavelengths (1505–1524 nm), mode-locking was typically self-starting at a pumping power of 600 mW, resulting in output power of around 10 mW. On the other hand, at longer wavelengths (1530–1561 nm), pumping power of only 400 mW could lead to self-starting with output power of around 5 mW. When mode-locking starts, the proposed mode-locked laser emits femtosecond pulses with a temporal spacing of 4 ns, corresponding to a repetition rate of 250 MHz, as shown in Fig. 3a and b. Stable pulse trains of the mode-locked laser were measured for more than 2000 ns without notable amplitude fluctuations, and a single pulse was clearly recorded, as shown in the zoomed-in view in the figure. Figure 3c shows the RF spectrum at a fundamental repetition rate of 250 MHz with both the resolution and video bandwidth set to 3.3 Hz. We measured a signal-to-noise ratio of 70 dB at a fundamental repetition rate of 250 MHz. We also measured the RF spectrum during repetition rate tuning from 249.8 to 252.2 MHz, as shown in the inset of Fig. 3c.

RF domain characteristics of the C-band tunable mode-locked laser: (a) output pulse trains over 2000 ns. (b) Zoomed-in view of Fig. 2a for 20 ns. (c) RF spectrum at the fundamental repetition rate with a resolution bandwidth and video bandwidth of 3.3 Hz. The inset shows the tunability of the repetition rate from 249.8 to 252.2 MHz with a resolution bandwidth and video bandwidth of 15 kHz.

The optical characteristics of the mode-locked laser are described in Fig. 4. Figure 4a shows the measurement results of the optical spectrums and the output power outputs when tuning the center wavelength from 1505 to 1561 nm, which fully covers the C-band (1530–1565 nm). Note that this also covers the absorption line of many greenhouse gases, including NH3, C2H2, CO2, HCN and CO. Moreover, it can cover the absorption line of 13C0H2 near 1542 nm and 85Rb near 778 nm by means of second harmonic generation, which are the recommended absorption lines for the length standard by BIPM (Bureau international des poids et mesures)40. Importantly, the individual comb modes of the proposed mode-locked laser can have much more optical power than previous wavelength-tunable mode-locked lasers due to the high-repetition rate, which allows a better signal-to-noise ratio. At an incidence angle of 0°, the mode-locked laser typically showed a center wavelength of 1561 nm, a 3-dB spectral bandwidth of 5.1 nm, a pulse duration (fitted to the Sech2 curve) of 640 fs and output power of 5.1 mW, as shown in Fig. 4a and b. As the transmission spectrum of the optical bandpass filter was shifted toward a shorter wavelength by increasing the incidence angle, the center wavelength of the mode-locked laser was also shifted toward a shorter wavelength, as shown in Figs. 2b and 4a. We observed the deterministic generation of the mode-locked laser simply by tilting the incidence angle of the intra-cavity light. Note that the optical bandpass filter also had an influence on a suppression of Kelly sidebands, despite the fact that the bandwidth of the optical bandpass filter was notably larger than the spectral bandwidth of the mode-locked laser41. For stable mode-locking states, the output power typically ranged from 5 to 9 mW, except for a certain regime, in this case 1516 nm to 1524 nm. The gain of the Er-doped fiber was low at shorter wavelengths of 1505 nm to 1524 nm42. When increasing the wavelength, the output power was gradually increased from 6 to 15 mw due to the higher gain.

Optical characteristics of the C-band tunable mode-locked laser: (a) Spectral characteristics measured by an optical spectrum analyzer from 1500 to 1580 nm. The upper part shows the output power at the moment of self-starting, or at the minimum pump power. The lower part shows several important absorption lines on the C-band wavelength. SHG: second harmonic generation (b) Optical autocorrelation measurement for evaluating the pulse durations.

The optical spectrums in the entire range of the center wavelength were well fitted to the Sech2 curve, indicative of typical soliton pulses. Figure 5 shows examples of the optical spectrum (gray color) with Sech2 curve fitting (red color) and Gaussian curve fitting (blue color) for comparison. As shown in Fig. 5a–c, the measured spectrums of the mode-locked laser were well matched with both the Sech2 curve and the Gaussian curve near the center wavelengths. However, far from the center wavelength, the measured spectrums were well matched not to the Gaussian curve but to only the Sech2 curve. This clearly shows that the proposed laser operated in the soliton mode-locking regime.

| Curve fittings of some examples of the optical spectrum to Gaussian and Sech2 curves: Curve fitting results for the center wavelengths of (a) 1505 nm, (b) 1527 nm, and (c) 1561 nm.

Figure 6 quantitatively presents in more detail the time bandwidth product, the pulse duration, and the 3-dB spectral bandwidth of the optical spectrum for each center wavelength. Pulse durations typically ranged from 640 fs to 2.8 ps assuming a Sech2 pulse shape, while the 3-dB spectral bandwidths ranged from 0.9 to 5.1 nm. However, they do not seem to have dependency on the center wavelength. The time bandwidth product, defined as the product of the temporal and spectral, were typically close to 0.315, corresponding to transform-limited Sech2 pulses. For some center wavelengths, time bandwidth products exceeding 0.315 were observed, as reported in previous studies18,23,30, likely caused by wavelength-dependent intracavity conditions such as cavity loss, gain, dispersion and SESAM.

Summary of the optical characteristics of the C-band tunable mode-locked laser. The upper section, middle section and lower section show the time bandwidth product, pulse duration, and optical 3-dB bandwidth, respectively.

In this article, we proposed and demonstrated a Fabry–Perot linear cavity-based C-band wavelength-tunable mode-locked polarization-maintaining fiber laser. With a modified laser cavity design using the bulk bandpass filter in our previous study, we dramatically scaled the repetition rate up from 125 MHz of our previous study35 to 250 MHz, which is the highest repetition rate for a C-band tunable mode-locked laser thus far to the best of our knowledge. A wide wavelength-tunable range of 1505 nm to 1561 nm was successfully realized with turn-key operation of soliton mode-locking merely by adjusting the incidence angle of the intra-cavity light in the cavity. This simple layout enables the proposed laser to be stably and robustly operated in actual cases. The proposed laser has a repetition rate of 250 MHz, which is good enough to be exploited in most high-precision frequency comb applications, such as high-precision optical dimensional metrology, broadband spectroscopy, and high-capacity optical communications. More importantly, unlike conventional combs, the remarkably high optical power of the individual comb modes is expected to allow an improvement of the signal-to-noise ratio, thus enabling tasks that were previously difficult to perform in various applications.

The datasets used and/or analyzed during the current study available from the corresponding author on reasonable request.

Diddams, S. A., Vahala, K. & Udem, T. Optical frequency combs: Coherently uniting the electromagnetic spectrum. Science 369, eaay3676 (2020).

Article CAS PubMed Google Scholar

Kim, J., Cox, J. A., Chen, J. & Kartner, F. X. Drift-free femtosecond timing synchronization of remote optical and microwave sources. Nat. Photon. 2(12), 733–736 (2008).

Article ADS CAS Google Scholar

Picque, N. & Hansch, T. W. Frequency comb spectroscopy. Nat. Photon. 13(3), 146–157 (2019).

Article ADS CAS Google Scholar

Nakamura, T. et al. Coherent optical clock down-conversion for microwave frequencies with 10–18 instability. Science 368, 889–892 (2020).

Article ADS CAS PubMed Google Scholar

Coddington, I., Swann, W. C., Nenadovic, L. & Newbury, N. R. Rapid and precise absolute distance measurements at long range. Nat. Photon. 3(6), 351–356 (2009).

Article ADS CAS Google Scholar

Jang, Y.-S. et al. Comb-referenced lase distance interferometer for industrial nanotechnology. Sci. Rep. 6, 31770 (2016).

Article ADS CAS PubMed PubMed Central Google Scholar

Jin, J. Dimensional metrology using the optical comb of a mode-locked laser. Meas. Sci. Tech. 27(2), 022001 (2016).

Article ADS Google Scholar

Jang, Y.-S. et al. Nanometric precision distance metrology via hybrid spectrally resolved and homodyne interferometry in a single soliton frequency microcomb. Phys. Rev. Lett. 126(2), 023903 (2021).

Article ADS CAS PubMed Google Scholar

Yamagiwa, M. et al. Multicascade-linked synthetic wavelength digital holography using an optical-comb-referenced frequency synthesizer. Opt. Express 26(20), 26292–26306 (2018).

Article ADS CAS PubMed Google Scholar

Li, Y. et al. "Real-time transition dynamics and stability of chip-scale dispersion-managed frequency microcombs". Light Sci. Appl. 9, 52 (2020).

Article ADS PubMed PubMed Central Google Scholar

Fermann, M. E. & Ingmar, H. Ultrafast fibre lasers. Nat. Photon. 7(11), 868–874 (2013).

Article ADS CAS Google Scholar

Sobon, G., Sotor, J. & Abramski, K. M. Passive harmonic mode-locking in Er-doped fiber laser based on graphene saturable absorber with repetition rates scalable to 2.22 GHz. Appl. Phys. Lett. 100(16), 161109 (2012).

Article ADS Google Scholar

Sinclair, L. C. et al. Operation of an optically coherent frequency comb outside the metrology lab. Opt. Express 22(6), 6996–7006 (2014).

Article ADS CAS PubMed Google Scholar

Martinez, A. & Yamashita, S. 10GHz fundamental mode fiber laser using a graphene saturable absorber. Appl. Phys. Lett. 101(4), 041118 (2012).

Article ADS Google Scholar

Tamura, K., Ippen, E. P., Haus, H. A. & Nelson, L. E. 77-fs pulse generation from a stretched-pulse mode-locked all-fiber ring laser. Opt. Lett. 18(13), 1080–1082 (1993).

Article ADS CAS PubMed Google Scholar

Keller, U. et al. Solid-state low-loss intracavity saturable absorber for Nd: YLF lasers: An antiresonant semiconductor Fabry-Perot saturable absorber. Opt. Lett. 17(7), 505–507 (1992).

Article ADS CAS PubMed Google Scholar

Keller, U. et al. Semiconductor saturable absorber mirrors (SESAM's) for femtosecond to nanosecond pulse generation in solid-state lasers. IEEE J. Sel. Top. Quantum Electron. 2(3), 435–453 (1996).

Article ADS CAS Google Scholar

Wang, F. et al. Wideband-tuneable, nanotube mode-locked, fibre laser. Nat. Nanotech. 3(12), 738–742 (2008).

Article ADS CAS Google Scholar

Bao, Q. et al. Atomic-layer graphene as a saturable absorber for ultrafast pulsed lasers. Adv. Funct. Mat. 19(19), 3077–3083 (2009).

Article CAS Google Scholar

Jhon, Y. I. et al. Metallic MXene saturable absorber for femtosecond mode-locked lasers. Adv. Mat. 29(40), 1702496 (2017).

Article Google Scholar

Kartner, F. X., Jung, I. D. & Keller, U. Soliton mode-locking with saturable absorbers. IEEE J. Sel. Top. Quantum Electron. 2(3), 540–556 (1996).

Article ADS CAS Google Scholar

Jang, H. et al. Polarization maintaining linear cavity Er-doped fiber femtosecond laser. Laser Phys. Lett. 12(10), 105102 (2015).

Article ADS Google Scholar

Sun, Z. et al. A stable, wideband tunable, near transform-limited, graphene-mode-locked, ultrafast laser. Nano Res. 3(9), 653–660 (2010).

Article CAS Google Scholar

Meng, Y. et al. Mode-locked Er:Yb-doped double-clad fiber laser with 75-nm tuning range. Opt. Lett. 40(7), 1153–1156 (2015).

Article ADS CAS PubMed Google Scholar

Wang, J., Ping Zhang, A., Shen, Y. H., Tam, H.-Y. & Wai, P. K. A. Widely tunable mode-locked fiber laser using carbon nanotube and LPG W-shaped filter. Opt. Lett. 40(18), 4329–4332 (2015).

Article ADS CAS PubMed Google Scholar

Li, D. et al. Wavelength and pulse duration tunable ultrafast fiber laser mode-locked with carbon nanotubes. Sci. Rep. 8, 2738 (2018).

Article ADS PubMed PubMed Central Google Scholar

Zou, C. et al. Wavelength-tunable passively mode-locked Erbium-doped fiber laser based on carbon nanotube and a 45◦ tilted fiber grating. Opt. Commun. 406, 151–157 (2017).

Article ADS Google Scholar

Jiang, X. et al. Wavelength-tunable all-fiber mode-locked laser based on supermode interference in a seven-core fiber. Appl. Opt. 57(23), 6768–6771 (2018).

Article ADS CAS PubMed Google Scholar

Wu, P. et al. Wavelength-tunable passively mode-locked all-fiber laser at 1.5 μm. Appl. Opt. 58(19), 5143–5147 (2019).

Article ADS CAS PubMed Google Scholar

Nyushkov, B., Kobtsev, S., Antropov, A., Kolker, D. & Pivtsov, V. Femtosecond 78-nm tunable Er: Fibre laser based on drop-shaped resonator topology. J. Light Tech. 37(4), 1359–1363 (2019).

Article CAS Google Scholar

Lu, B. et al. Widely Wavelength-Tunable Mode-Locked Fiber Laser Based on a 45°-Tilted Fiber Grating and Polarization Maintaining Fiber. J. Light Tech. 37(14), 3571–3578 (2019).

Article CAS Google Scholar

Wang, W. et al. Tunable mode-locked erbium-doped fiber laser based on a digital micro-mirror device. Appl. Opt. 59(11), 3440–3446 (2020).

Article ADS CAS PubMed Google Scholar

Armas-Rivera, I. et al. Wide wavelength-tunable passive mode-locked Erbium-doped fiber laser with a SESAM. Opt. Laser Tech. 134, 106593 (2021).

Article CAS Google Scholar

Tsai, L.-Y., Li, Z.-Y., Lin, J.-H., Song, Y.-F. & Zhang, H. Wavelength tunable passive-mode locked Er-doped fiber laser based on graphene oxide nano-platelet. Opt. Laser Tech. 140, 106932 (2021).

Article CAS Google Scholar

Jang, Y.-S., Park, J. & Jin, J. Linear-cavity Er-doped fiber mode-locked laser with large wavelength tunability. Appl. Opt. 61(34), 10116–10120 (2022).

Article ADS CAS PubMed Google Scholar

Kim, W. et al. Absolute laser ranging by time-of-flight measurement of ultrashort light pulses [Invited]. J. Opt. Soc. Am. A 37(9), B27–B35 (2020).

Article CAS Google Scholar

Hansel, W. et al. All polarization-maintaining fiber laser architecture for robust femtosecond pulse generation. Appl. Phys. B 123(1), 41 (2017).

Article ADS Google Scholar

Lumeau, J., Lemarchand, F., Begou, T., Arhilger, D. & Hagedorn, H. Angularly tunable bandpass filter: Design, fabrication, and characterization. Opt. Lett. 44(7), 1829–1832 (2019).

Article ADS CAS PubMed Google Scholar

Jang, Y.-S. et al. Space radiation test of saturable absorber for femtosecond laser. Opt. Lett. 39(10), 2831–2834 (2014).

Article ADS PubMed Google Scholar

Quinn, T. J. Practical realization of the definition of the metre, including recommended radiations of other optical frequency standards (2001). Metrologia 40(2), 103–133 (2003).

Article ADS MathSciNet Google Scholar

Tao, J. et al. Sideband-free tunable and switchable dual-wavelength mode-locked fiber laser based on the Lyot filter and spontaneous radiation peaks. Opt. Express 30(10), 17465–17475 (2022).

Article ADS CAS PubMed Google Scholar

Giles, C. R. & Desurvire, E. Modeling erbium-doped fiber amplifiers. J. Light. Technol. 9(2), 271–283 (1991).

Article ADS CAS Google Scholar

Download references

The authors acknowledge support from Korea Research Institute of Standards and Science (23011041, 22011230).

Length Group, Korea Research Institute of Standards and Science, Daejeon, 34113, Republic of Korea

Yoon-Soo Jang, Jungjae Park & Jonghan Jin

Major in Precision Measurement, University of Science and Technology, Daejeon, 34113, Republic of Korea

Jungjae Park & Jonghan Jin

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

Y.-S. J. designed and led the work. Y.-S. J. performed the experiments. Y.-S. J., J. P. and J. J. conducted the analysis of the measured data. Y.-S. J. and J. J. prepared the manuscript. All authors reviewed the manuscript.

Correspondence to Jonghan Jin.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Jang, YS., Park, J. & Jin, J. Full C-band wavelength-tunable, 250 MHz repetition rate mode-locked polarization-maintaining fiber laser. Sci Rep 13, 3623 (2023). https://doi.org/10.1038/s41598-023-30532-z

Download citation

Received: 16 December 2022

Accepted: 24 February 2023

Published: 03 March 2023

DOI: https://doi.org/10.1038/s41598-023-30532-z

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.